Dummy War Weapons: The Complete Guide to 3D-Printed Arsenal for Dummy 13 Figures
Build a battle-ready arsenal for your Dummy 13 figure. Print, scale, and finish custom Dummy War Weapons with tested settings, materials, and tips.
Why Dummy War Weapons Are the Fastest Upgrade for Your Dummy 13
A stock Dummy 13 is a great little figure — and a fairly boring one. The moment you snap a rifle into that articulated hand, the print stops being a desk toy and becomes a character with a story. That is the entire appeal of Dummy War Weapons: a fast-growing, community-driven arsenal of printable pistols, blades, launchers, and shields built specifically around the Dummy 13 frame.
If you have already printed the base figure, you already own the hardest part. Dummy War Weapons cost pennies in filament, print in under an hour for most sidearms, and completely change how the figure photographs, displays, and plays. This guide covers what to print first, how to make grips actually fit, which materials survive handling, and where to find files worth your spool time.
A quick note on sourcing: this article draws on general 3D printing practice plus community reports from Dummy 13 builders. Curated collections — like the Dummy 13 weapons collection assembled by TechLeak on Printables, the 3D printing community and model repository — are a practical starting point, though individual file quality varies wildly.
The Core Arsenal: Which Dummy War Weapons to Print First
Not all weapons are equally beginner-friendly. Small, flat, single-piece designs succeed on almost any printer. Multi-part rifles with pins, sliding bolts, and removable magazines demand tighter tolerances and a bit of patience. The table below reflects typical player experience with a 0.4 mm nozzle at 0.2 mm layer height.
| Weapon category | Typical print time | Difficulty | Key challenge | Best for |
|---|---|---|---|---|
| Pistol (single piece) | 45–90 min | Easy | Grip peg fit | First print, test fit |
| Energy blade / saber | 30–60 min | Easy | Thin tip snapping | Photogenic display |
| Melee club or hammer | 1–2 h | Easy | Balance when held | Quick army builds |
| Greatsword | 2–3 h | Easy–Moderate | Warping on long blades | Hero shots |
| Assault rifle (multi-part) | 2–4 h | Moderate | Pin alignment | Centerpiece loadouts |
| Shield | 1.5–3 h | Easy | Strap geometry | Squad dioramas |
| Heavy launcher | 4–6 h | Hard | Supports + weight | Veteran builders |
| Weapon rack / armory | 3–5 h | Moderate | Bed size | Displaying a collection |
A sensible first order is pistol, then energy blade, then a two-part rifle. Each step teaches one new skill — grip fit, thin-wall strength, then alignment — without stacking problems.
Start With a Test Couplet
Before committing to a six-hour launcher, print a single small grip test. It takes about eight minutes and tells you whether your printer's tolerance matches the model's designed peg. Community reports consistently show that a 0.2–0.3 mm clearance is the sweet spot: tight enough to hold a pose, loose enough to swap weapons without pliers.
Scale, Grips, and Tolerances: Making Dummy War Weapons Fit
Dummy 13 stands roughly 6 inches (about 15 cm) at 100% scale, which places it close to 1/12 scale. That matters because it means a huge library of accessories designed for 6-inch action figures, Gunpla parts, and 1/12 diorama props can be adapted — sometimes with zero edits.
| Parameter | Recommended starting point | Why it matters |
|---|---|---|
| Nozzle size | 0.4 mm | Best balance of detail and speed for small parts |
| Layer height | 0.12–0.2 mm | 0.12 mm for barrels and sights, 0.2 mm for bulk |
| Wall count | 3 perimeters | Thin blades and barrels need hoop strength |
| Infill | 15% for bodies, 100% for grip pegs | Pegs take all the stress |
| Print orientation | Barrels horizontal, blades vertical | Layer lines should run along the length |
| Brim | Yes, on parts under 20 mm | Stops tiny sights and triggers from popping off |
| Cooling | Full after layer 3 | Sharpens overhangs on trigger guards |
| Horizontal expansion | +0.05 to +0.1 mm | Fixes tight grip sockets |
The Grip Is the Whole Game
Every Dummy War Weapons project lives or dies at the hand. Measure the peg diameter on your specific print — resin printers and FDM printers produce noticeably different results — then scale the weapon's grip socket, not the entire model. Scaling the whole weapon changes the silhouette and makes a rifle look like a toy rifle.
Three quick fixes, in order of preference:
- Scale only the grip section in your slicer's per-part scaling if the file is split.
- Drill or ream the socket with a 2 mm bit for a friction fit.
- Add a thin wrap of electrical tape or a drop of hot glue for a removable, snug hold.
Material Choices That Survive Play
The best-looking filament is rarely the toughest, and weapons take abuse at the thinnest points — muzzles, blade tips, and magazine wells.
| Material | Strength | Detail | Cost | Best use |
|---|---|---|---|---|
| PLA | Low–Moderate | Excellent | $ | Display pieces, painted props |
| PLA+ / tough PLA | High | Excellent | $ | General-purpose Dummy War Weapons |
| PETG | High | Good | $$ | Functional parts, heat resistance |
| ABS / ASA | High | Good | $$ | Solvent-smoothed, durable builds |
| TPU (95A) | Flexible | Low | $$$ | Grip wraps, straps, slings |
| Resin (standard) | Low | Outstanding | $$$ | Sights, scopes, fine greebles |
A hybrid approach works best for most builders: print the body in PLA+ for toughness, then swap in a resin scope or sight for crisp detail. Translucent PETG or clear PLA makes convincing energy blades, especially with a cool white LED hidden in the hilt.
Where to Find Dummy War Weapons Files Worth Printing
File quality is the single biggest variable in this hobby. A gorgeous render means nothing if the model has non-manifold geometry or a 0.05 mm peg clearance. Use the table below as a vetting checklist.
| Source type | Strength | Watch out for |
|---|---|---|
| Printables collections | Curated, remix-friendly, easy licensing | Dead links, unupdated versions |
| Thingiverse | Huge back catalog | Older files with rough meshes |
| MakerWorld | Print profiles included | Profile tuned to one printer only |
| Cults3D | High-quality paid designs | Cost adds up fast |
| MyMiniFactory | Pre-supported resin options | Smaller selection for figures |
Always check the license. Many Dummy 13 accessories are remixes of a free base model, which means non-commercial terms often apply — fine for personal armies, not fine for selling prints at a con.
A Five-Minute Vetting Routine
- Open the model in your slicer and check for floating shells in preview.
- Look for a stated peg or socket dimension in the description.
- Read the newest comments, not the oldest — they reflect the current file version.
- Confirm the designer posted print photos, not just renders.
- Check whether the model is split for multicolor; single-color prints of split files often look worse.
Finishing, Balancing, and Displaying Your Loadout
Raw prints look like raw prints. Ten minutes of post-processing turns a Dummy War Weapons piece from "3D printed" into "bought at a store."
| Step | Tool | Time | Effect |
|---|---|---|---|
| Remove supports | Flush cutters, hobby knife | 2 min | Clean silhouette |
| Sand contact points | 400 then 800 grit | 5 min | Removes layer ridges |
| Prime | Gray filler primer, 2 light coats | 15 min + dry | Reveals flaws, bonds paint |
| Base coat | Acrylic, airbrush or rattle can | 10 min | Unified color |
| Wash | Black or brown wash | 5 min | Instant depth in recesses |
| Drybrush | Silver or gunmetal | 5 min | Edge wear and metal shine |
| Seal | Matte or satin varnish | 5 min | Survives handling |
Balancing Heavy Weapons
A long launcher printed in PLA feels like a balloon on a stick. Community builders solve this by pausing the print at 70% height and dropping in a few steel nuts, washers, or a cut section of 3 mm brass rod inside the body. The added mass sits right where the hand grips, so the figure holds a natural pose instead of tipping forward.
For storage, a shallow foam-lined tray with labeled compartments keeps muzzles and blade tips from snapping. If you build a full army, print a matching weapon rack — it doubles as a display and as a parts organizer.
FAQ
What exactly are Dummy War Weapons? It is the community shorthand for the printable guns, blades, shields, and heavy gear designed or scaled to fit the Dummy 13 articulated figure. Most are free remixes shared on model repositories, and nearly all are small enough to print in an afternoon.
Will Dummy War Weapons fit other 6-inch figures? Often, yes. Dummy 13 is close to 1/12 scale, so many accessories designed for 6-inch action figures or 1/12 dioramas work with minor grip adjustments. Marvel Legends and similar figures usually need a thicker peg, while Gunpla hands need a smaller one.
What filament should I use for Dummy War Weapons? PLA+ is the safest default: it is stiff, cheap, and prints clean detail. Use PETG for anything that will be handled or left in a hot car, TPU for grip wraps, and resin for small optical parts like scopes.
Are these weapon files legal to print and share? Printing for personal use is almost always fine. Redistributing or selling prints depends entirely on the designer's license — many Dummy 13 accessories carry non-commercial or remix-only terms, so read the listing before you list anything on a storefront.
By DummyWar Wiki TeamUpdated
Related Guides
Dummy War Ballistics Explained: How Ballistic Dummies Test Real Combat Ammo
Dummy war ballistics turns raw ammo specs into real-world data. See how ballistic dummies are built, calibrated, and used to judge combat loads.
Dummy War Drones: Drone Operator Class, Dead Ground Map, and RPG-7 Guide
Dummy War Drones arrive in DummyWar's next update alongside the Dead Ground map and an RPG-7 gunner. Here's how the new drone class changes combat.
Dummy War Guns: A Complete Guide to 3D-Printed Weapons for Dummy 13
Dummy War Guns explained: the best 3D-printed weapons for Dummy 13, print settings, scaling fixes, cost estimates, and loadout ideas from the community.
Dummy War RPG Weapons Guide: Units, Statues and Winning Loadouts
A practical Dummy War RPG weapons guide covering unit roles, statue abilities, attack-vs-defend timing, and loadouts for late-stage pushes.